COMBER

Combing is the process which is used to upgrade the raw material. It influences the following yarn quality

1. yarn evenness
2. strength
3. cleanness
4. smoothness
5. visual appearance

TASK OF THE COMBER:
To proudce an improvement in yarn quality, the comber must perform the following operation.

1. elimination of short fibres
2. elimination of remaining impurities
3. elimination of neps

• The basic operation of the comber is to improve the mean length or staple length by removing the
  short fibres.
  • Since fineness of short fibres(noil) is low, the overall micronaire of the sliver after combing is high.
    
  • Because of combing, fibre parallelisation increases. Please note that this is a side effect which
    is not an advantage always. The high degree of parallelisation might reduce inter-fibre adhesion in the sliver to
    such an extent that the fibres slide apart while pulled out of the can. This may lead to sliver breaks or false draft.
  • SEQUENCE OF OPERATION IN A COMBER
    1. Feeding, lap is fed by feed roller
    2. fed lap gripped by the nipper
    3. gripped lap is combed by circular comb
    4. detaching roller grips the combed lap and moves forward
    5. while the detaching roller delivers the material, top comb comes into action to further clean the lap
    6. While going back,nipper opens and receives a new bit of lap
  • The rawmaterial delivered by the carding machine can not be fed directly to the comber. Lap preparation is a must
    A good lap fed to the comber should have
    
    1. highest degree of evenness so that lap is gripped uniformly by the nipper
    2. a good parallel disposition of fibres so that long fibres will not be lost in the noil
    3. trailing hooks from carding should be fed as leading hooks to reduce long fibre loss in the noil
  • Degree of parallelisation of lap fed to the combers should be optimum. If fibres are over parallelised
    lap licking will be a major problem. Because of fibre to fibre adhesion, mutual separation of layers within the sheet
    is very poor.Moreover the retaining power of the sheet can be strongly reduced that it is no longer able to hold
    back the neps as it usually does. Some of these neps also pass thro the top comb. Neppiness of the web is increased.
  • -

  • Retaining power of the fibres results in self cleaning of the lap during combing operation. A thick sheet always
    exerts a greater retaining power than a thin one.To certain extent, the bite of the nipper is more effective with
    a higher sheet volume.On the negative side , a thick sheet always applies a strong load to the comb and this
    can lead to uncontrolled combing.A compromise should be struck between quality and productivity.
  • If the sheet is more even across the width, clamping effect at the bite of the nipper will be better.
    Evenness of the lap is therefore of considerable significance. The most effective method of obtaining a
    high degree of evenness of the sheet is through more number of doublings in the web form.
    (as it is done in RIBBON LAP)
  • Fibres must be presented to the comber so that leading hooks predominate in the feedstock. This influences
    not only the opening out of the hooks themselves, but also the cleanliness of the web.If the sheet is fed
    to the comber in the wrong direction, the number of neps rises markedly.
  • Both quantity and form of fibre hooks depend mainly upon the stiffness of the fibres. This rises to the
    second or third power with fine fibres. Fine and long fibres will always exhibit more
    and longer hooks than short and coarse fibres. Accordingly, the role of fibre hooks in the spinning process
    becomes more significant as fibres become finer.
  • There are two types of feeds in COMBER
    1. Forward feed (concurrent feed):Feed of the sheet into the nippers occurs while the nippers move towards
       the detaching roller
    2. Backward feed (counter-feed) : Feed of the sheet occurs during return of the nippers
  • Higher Noil % always improves the imperfections in the final yarn. But the strength and other qality parameters
    improve upto certain noil %, further increase in noil results in quality detrioration.
  • In backward feed, the cylinder comb combs through the fibres more often than in forward feed
    Therefore, the elimination of impurities and neps is always good. However the difference is usually undetectable
    in modern high performance combers of the latest generation.
  • -

  • The FEED LENGTH has a direct influence on production rate, noil %, and the quality of combing. High feed
    length increases the production rate but cause deterioration in quality. Higher the quality requirement,
    feed length should be lower. To some extent , the feed length may be decided by the length of the fibre also.

    Detaching length is the distance between the bite of hte nippers and the nip of the detaching rollers.
    This distance direectly affects the noil %. More the detaching distance, higher the elimination of noil.

  • Needles of the top comb have a flattened cross section and are used with a point density in the range of
    22 to 32 needles per centimeter. More the needles, more the noil%.
  • The Depth of Penetration of top comb also affects the Noil %. If the comb depth is increased by 0.5mm,
    approximately 2% increase in noil will occur. When the depth is increased , the main improvement in
    quality is seen in Neps.Over deep penetration of top comb disturbs fibre movement during piecing which will
    deteriorate the quality.
  • Since the web from detaching roller is intermittent because of the intermittent functions like feeding,
    combing and detaching, to have a continuous web from the comber,fibre fringes are laid on the top of each
    other in the same way as roofting tiles. This process is called Piecing. This is a distinct source of fault
    in the operation of Rectinlinear Combing. The sliver produced in this way exhibits a periodic variation.
  • As large a lap as possible with adapted lap weight which is as high and as uniform as possible
    must be positioned in front of the comber. The better the comber lap is prepared, the heavier the lap weight
    can be set on the comber and the less the resultant noil waste with the same degree of cleanliness of the
    yarn.
  • The higher degree of combing out are used in order to permit final spinning of ultra-fine yarns or
    to increase the strength of a yarn. Reducing the lint content improves the medium staple. However, not all
    cottons meet these requirements. Low degree of combing out , on the other hand, frequently serve to improve
    purity. When the card sliver is pulled through the needle bars, these separate off foreign bodies, large neps
    and torn fibres. Light combing out has also been introduced to a greater extent owing to the impairments in
    cotton purity influenced by mechanical harvesting. Even when combing with minimum noil percentages, there
    is a noticeable improvement in fibre parallelsim in the sliver. Even the smoothness and shine of the yarn are
    improved. It must thus be anticipated that this method will become more and more popular in the future.
  • Production of the comber is dependent upon the following
    1. N- Nips per min
    2. S- feed in mm/nip
    3. G- lap weight in g/m
    4. K- Noil percentage
    5. A- tension draft between lap and feed roller(from 1.05 to 1.1)
    6. E- efficiency
    Production = (E * N * S * G * (100-K) * 60 * 8) / (1000 * 1000 * A *100)  

visit our HOME PAGE for complete list of Textile articles